Thursday, 12 May 2016

Week 12- Make the calibration of ultrasonic sensor and Motor of car


   from this week, to calibrate the ultrasonic sensor and motor, I must troubleshooting the coding because car can't go straight because one of the Tyre got problem. The sensor will sense the object front and behind the car.



 make the  object to car to sense the object using ultrasonic sensor.


make the calibration of ultrasonic sensor and test  to drive the car to follow .
until location

Monday, 2 May 2016

Week 11- Make the track to car move straight


     In this week, I locate the palace to find the shop that sell the big card board. Pustaka Rakyat sell the card board that available to me to create the track car. By using  card board and I implement to create the track that will drive the car to locate the location.

     Besides that, after I create the track and make the testing of ultrasonic to sense the track and the car can drive bye following the the track to the location

By using card board and make the track of car

The track will drive the car to locate the location 



Week 10 - FYP2 briefing #4

FYP briefing #4 final report writing workshop S1 2016


1) To explain all student FYP2 how to write a strong thesis statement
2) content to include in final report and distribution odd percentage



During this week 10 basically student was exposed to briefing about making the final report for FYP2. The briefing was conducted by madam Pusparini Dewa Abdul Aziz in TTL hall from 2.30pm until 5.30 and attendace of all student that taking the FYP was compulsory.





During the briefing, the FYP committee has given briefing us about the point that must put in thesis :

1. Abstract
2. Introduction
3. literature review
4. Methodology
5. Result and Discussion
6. Conclusion and Future development
7. References
8. Organization/Format


Tuesday, 19 April 2016

Week 9 - combine circuit and hardware


For this week i try to combine the circuit with the hardware.


This picture shown the circuit that want to combine with the car. The circuit have done test at last week

This picture shown car model that i buy at Jalan Pasar at rm 42.00. This car model car model come for two dc motor 6v.

this picture shown the combine circuit and hardware. the sensor from the circuit i put at front and behind the car.


Saturday, 9 April 2016

WEEK 8 - Test the component (LCD)


First step of constructing the LCD with arduino is to construct the overall look of the interface.



During test this LCD i got one problem. The LCD has "bug" when the motor is running.
I try to fix this problem, put the capacitor to filter the current but the problem still can't fix



conclusion:

  After reseach this problem at internet to fix this problem i must use the Driver motor L293D shield





Saturday, 26 March 2016

Week 7- Make the PCB

Step to etching pcb
Step 1: Design

Step 2: Print out the design onto the shiny side of the transfer paper

Step 3: Sand the copper plate so there is a rough surface for the design to stick to when transferred

Step 4: Wash the copper with some water and rubbing alcohol and let it dry

Step 5: Cut out the designs and place them face down on the copper

Step 6: Run the copper plate with the design face down through a laminator 5-7 times until the plate is hot

Step 7: After running the plate through a laminator or iron place the plate into a cold bath and agitate until the paper floats off

Step 8: Place the PCB into the etching solution and agitate for 25-30 minutes or until all the copper has dissolved around the design

Step 9: Once all the copper is gone rinse it in the water bath, let it dry and use rubbing alcohol to whip off the ink transferred onto the PCB

Step 10: And now you have an etched PCB board but you still need to drill the holes





WEEK 6 - Test the component



First step of constructing the sensor Interface with arduino is to construct the overall look of the interface.
Overall look :



After completing the look of the sensor, the source code need to be added in order for the interface to work. The source has the code needed for the interface to interact with the arduino and sensor.